Hubei University

Oil spills and industrial organic pollutants have induced severe water pollution and threatened every species in the ecological system. To deal with oily water, special wettability stimulated materials have been developed over the past decade to separate oil-and-water mixtures. Basically, synergy between the surface chemical composition and surface topography are commonly known as the key factors to realize the opposite wettability to oils and water and dominate the selective wetting or absorption of oils/water. In this review, we mainly focus on the development of materials with either super-lyophobicity or super-lyophilicity properties in oil/water separation applications where they can be classified into four kinds as follows (in terms of the surface wettability of water and oils): (i) superhydrophobic and superoleophilic materials, (ii) superhydrophilic and under water superoleophobic materials, (iii) superhydrophilic and superoleophobic materials, and (iv) smart oil/water separation materials with switchable wettability. These materials have already been applied to the separation of oil-and-water mixtures: from simple oil/water layered mixtures to oil/water emulsions (including oil-in-water emulsions and water-in-oil emulsions), and from non-intelligent materials to intelligent materials. Moreover, they also exhibit high absorption capacity or separation efficiency and selectivity, simple and fast separation/absorption ability, excellent recyclability, economical efficiency and outstanding durability under harsh conditions. Then, related theories are proposed to understand the physical mechanisms that occur during the oil/water separation process. Finally, some challenges and promising breakthroughs in this field are also discussed. It is expected that special wettability stimulated oil/water separation materials can achieve industrial scale production and be put into use for oil spills and industrial oily wastewater treatment in the near future.

ADVERTISEMENT RETURN TO ISSUEPREVArticleNEXTAdvances in Homogeneous and Heterogeneous Catalytic Asymmetric EpoxidationQ.-H. Xia, H.-Q. Ge, C.-P. Ye, Z.-M. Liu, and K.-X. SuView Author Information Laboratory for Advanced Materials and New Catalysis, School of Chemistry and Materials Science, Hubei University, Wuhan 430062, China, Laboratory of Natural Gas Utilization and Applied Catalysis, Dalian Institute of Chemical Physics of Chinese Academy of Sciences, Dalian 116023, China, and Jingmen Technological College, Jingmen 448000, China Cite this: Chem. Rev. 2005, 105, 5, 1603–1662Publication Date (Web):April 19, 2005Publication History Received30 June 2004Published online19 April 2005Published inissue 1 May 2005https://pubs.acs.org/doi/10.1021/cr0406458https://doi.org/10.1021/cr0406458research-articleACS PublicationsCopyright © 2005 American Chemical SocietyRequest reuse permissionsArticle Views13194Altmetric-Citations884LEARN ABOUT THESE METRICSArticle Views are the COUNTER-compliant sum of full text article downloads since November 2008 (both PDF and HTML) across all institutions and individuals. These metrics are regularly updated to reflect usage leading up to the last few days.Citations are the number of other articles citing this article, calculated by Crossref and updated daily. Find more information about Crossref citation counts.The Altmetric Attention Score is a quantitative measure of the attention that a research article has received online. Clicking on the donut icon will load a page at altmetric.com with additional details about the score and the social media presence for the given article. Find more information on the Altmetric Attention Score and how the score is calculated. Share Add toView InAdd Full Text with ReferenceAdd Description ExportRISCitationCitation and abstractCitation and referencesMore Options Share onFacebookTwitterWechatLinked InRedditEmail Other access optionsGet e-Alertsclose SUBJECTS:Catalysts,Hydrocarbons,Ligands,Organic reactions,Stereoselectivity Get e-Alerts

BACKGROUND: Tumor-associated macrophages (TAMs) are major components of tumor microenvironment that frequently associated with tumor metastasis in human cancers. Circulating tumor cell (CTC), originating from primary tumor sites, is considered to be the precursors of tumor metastasis. However, the regulatory mechanism of TAMs in CTC-mediated tumor metastasis still remains unclear. METHODS: Immunohistochemical staining was used to detect the macrophages infiltration (CD68 and CD163), epithelial-mesenchymal transition (EMT) markers (E-cadherin and Vimentin) expression in serial sections of human colorectal cancer (CRC) specimens. Then, the correlations between macrophages infiltration and clinicopathologic features, mesenchymal CTC ratio, and patients' prognosis were analyzed. A co-culture assay in vitro was used to evaluate the role of TAMs on CRC EMT, migration and invasion, and ELISA, luciferase reporter assay and CHIP were performed to uncover the underlying mechanism. Furthermore, an in vivo model was carried out to confirm the effect of TAMs on mesenchymal CTC-mediated metastasis. RESULTS: TAMs infiltrated in invasive front was associated with EMT, mesenchymal CTC ratio, and poor prognosis in patients with CRC. CRC-conditioned macrophages regulated EMT program to enhance CRC cells migration and invasion by secreting IL6. TAMs-derived IL6 activated the JAK2/STAT3 pathway, and activated STAT3 transcriptionally inhibited the tumor suppressor miR-506-3p in CRC cells. miR-506-3p, a key miRNA regulating FoxQ1, was downregulated in CRC cells, resulting in increased FoxQ1 expression, which in turn led to the production of CCL2 that promoted macrophage recruitment. Inhibition of CCL2 or IL6 broke this loop and reduced macrophage migration and mesenchymal CTC-mediated metastasis, respectively. CONCLUSIONS: Our data indicates that TAMs induce EMT program to enhance CRC migration, invasion, and CTC-mediated metastasis by regulating the JAK2/STAT3/miR-506-3p/FoxQ1 axis, which in turn leads to the production of CCL2 that promote macrophage recruitment, revealing a new cross-talk between immune cells and tumor cells in CRC microenvironment.

Abstract Rechargeable aqueous Zn‐ion batteries promise high capacity, low cost, high safety, and sustainability for large‐scale energy storage. The Zn metal anode, however, suffers from the dendrite growth and side reactions that are mainly due to the absence of an appropriate solid electrolyte interphase (SEI) layer. Herein, the in situ formation of a dense, stable, and highly Zn 2+ ‐conductive SEI layer (hopeite) in aqueous Zn chemistry is demonstrated, by introducing Zn(H 2 PO 4 ) 2 salt into the electrolyte. The hopeite SEI (≈140 nm thickness) enables uniform and rapid Zn‐ion transport kinetics for dendrite‐free Zn deposition, and restrains the side reactions via isolating active Zn from the bulk electrolyte. Under practical testing conditions with an ultrathin Zn anode (10 µm), a low negative/positive capacity ratio (≈2.3), and a lean electrolyte (9 µL mAh −1 ), the Zn/V 2 O 5 full cell retains 94.4% of its original capacity after 500 cycles. This work provides a simple yet practical solution to high‐performance aqueous battery technology via building in situ SEI layers.

stimulates the immune function to produce a large number of white blood cells and neutrophils (2-4 times more than the control), thereby producing the synergistic antibacterial effects and accelerated wound healing.

BACKGROUND: Sirtuin 3 (SIRT3) is one of the seven mammalian sirtuins, which are homologs of the yeast Sir2 gene. SIRT3 is the only sirtuin with a reported association with the human life span. Peroxisome proliferator-activated receptor gamma coactivator-1alpha (PGC-1alpha) plays important roles in adaptive thermogenesis, gluconeogenesis, mitochondrial biogenesis and respiration. PGC-1alpha induces several key reactive oxygen species (ROS)-detoxifying enzymes, but the molecular mechanism underlying this is not well understood. RESULTS: Here we show that PGC-1alpha strongly stimulated mouse Sirt3 gene expression in muscle cells and hepatocytes. Knockdown of PGC-1alpha led to decreased Sirt3 gene expression. PGC-1alpha activated the mouse SIRT3 promoter, which was mediated by an estrogen-related receptor (ERR) binding element (ERRE) (-407/-399) mapped to the promoter region. Chromatin immunoprecipitation and electrophoretic mobility shift assays confirmed that ERRalpha bound to the identified ERRE and PGC-1alpha co-localized with ERRalpha in the mSirt3 promoter. Knockdown of ERRalpha reduced the induction of Sirt3 by PGC-1alpha in C(2)C(12) myotubes. Furthermore, Sirt3 was essential for PGC-1alpha-dependent induction of ROS-detoxifying enzymes and several components of the respiratory chain, including glutathione peroxidase-1, superoxide dismutase 2, ATP synthase 5c, and cytochrome c. Overexpression of SIRT3 or PGC-1alpha in C(2)C(12) myotubes decreased basal ROS level. In contrast, knockdown of mSIRT3 increased basal ROS level and blocked the inhibitory effect of PGC-1alpha on cellular ROS production. Finally, SIRT3 stimulated mitochondrial biogenesis, and SIRT3 knockdown decreased the stimulatory effect of PGC-1alpha on mitochondrial biogenesis in C(2)C(12) myotubes. CONCLUSION: Our results indicate that Sirt3 functions as a downstream target gene of PGC-1alpha and mediates the PGC-1alpha effects on cellular ROS production and mitochondrial biogenesis. Thus, SIRT3 integrates cellular energy metabolism and ROS generation. The elucidation of the molecular mechanisms of SIRT3 regulation and its physiological functions may provide a novel target for treating ROS-related disease.

Hypoxia, a typical feature of solid tumors, remarkably restricts the efficiency of photodynamic therapy (PDT). Here, a carbon nitride (C3N4)-based multifunctional nanocomposite (PCCN) for light-driven water splitting was used to solve this problem. Carbon dots were first doped with C3N4 to enhance its red region absorption because red light could be used to trigger the in vivo water splitting process. Then, a polymer containing a protoporphyrin photosensitizer, a polyethylene glycol segment, and a targeting Arg-Gly-Asp motif was synthesized and introduced to carbon-dot-doped C3N4 nanoparticles. In vitro study showed that PCCN, thus obtained, could increase the intracellular O2 concentration and improve the reactive oxygen species generation in both hypoxic and normoxic environments upon light irradiation. Cell viability assay demonstrated that PCCN fully reversed the hypoxia-triggered PDT resistance, presenting a satisfactory growth inhibition of cancer cells in an O2 concentration of 1%. In vivo experiments also indicated that PCCN had superior ability to overcome tumor hypoxia. The use of water splitting materials exhibited great potential to improve the intratumoral oxygen level and ultimately reverse the hypoxia-triggered PDT resistance and tumor metastasis.

Structural phase transitions can be used to alter the properties of a material without adding any additional elements and are therefore of significant technological value. It was found that the hexagonal-SnS2 phase can be transformed into the orthorhombic-SnS phase after an annealing step in an argon atmosphere, and the thus transformed SnS shows enhanced sodium-ion storage performance over that of the SnS2, which is attributed to its structural advantages. Here, we provide the first report on a SnS@graphene architecture for application as a sodium-ion battery anode, which is built from two-dimensional SnS and graphene nanosheets as complementary building blocks. The as-prepared SnS@graphene hybrid nanostructured composite delivers an excellent specific capacity of 940 mAh g(-1)and impressive rate capability of 492 and 308 mAh g(-1) after 250 cycles at the current densities of 810 and 7290 mA g(-1), respectively. The performance was found to be much better than those of most reported anode materials for Na-ion batteries. On the basis of combined ex situ Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and ex situ X-ray diffraction, the formation mechanism of SnS@graphene and the synergistic Na-storage reactions of SnS in the anode are discussed in detail. The SnS experienced a two-structural-phase transformation mechanism (orthorhombic-SnS to cubic-Sn to orthorhombic-Na3.75Sn), while the SnS2 experienced a three-structural-phase transformation mechanism (hexagonal-SnS2 to tetragonal-Sn to orthorhombic-Na3.75Sn) during the sodiation process. The lesser structural changes of SnS during the conversion are expected to lead to good structural stability and excellent cycling stability in its sodium-ion battery performance. These results demonstrate that the SnS@graphene architecture offers unique characteristics suitable for high-performance energy storage application.

The development of bifunctional electrocatalysts with high performance for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) with earth-abundant elements is still a challenge in electrochemical water splitting technology. Herein, we fabricated a free-standing electrocatalyst in the form of vertically oriented Fe-doped Ni3S2 nanosheet array grown on three-dimensional (3D) Ni foam (Fe-Ni3S2/NF), which presented a high activity and durability for both HER and OER in alkaline media. On the basis of systematic experiments and calculation, the Fe-doping was evidenced to increase the electrochemical surface area, improve the water adsorption ability, and optimize the hydrogen adsorption energy of Ni3S2, which resulted in the enhancement of HER activity on Fe-Ni3S2/NF. Moreover, metal sites of Fe-Ni3S2/NF were proved to play a significant role in the HER process. During the catalysis of OER, the formation of Ni–Fe (oxy)hydroxide was observed on the near-surface section of Fe-Ni3S2/NF, and the introduction of the Fe element dramatically enhanced the OER activity of Ni3S2. The overall water splitting electrolyzer assembled by Fe-Ni3S2/NF exhibited a low cell voltage (1.54 V @ 10 mA cm–2) and a high durability in 1 M KOH. This work demonstrated a promising bifunctional electrocatalyst for water electrolysis in alkaline media with potential application in the future.

The piezoelectric effect is widely applied in pressure sensors for the detection of dynamic signals. However, these piezoelectric-induced pressure sensors have challenges in measuring static signals that are based on the transient flow of electrons in an external load as driven by the piezopotential arisen from dynamic stress. Here, we present a pressure sensor with nanowires/graphene heterostructures for static measurements based on the synergistic mechanisms between strain-induced polarization charges in piezoelectric nanowires and the caused change of carrier scattering in graphene. Compared to the conventional piezoelectric nanowire or graphene pressure sensors, this sensor is capable of measuring static pressures with a sensitivity of up to 9.4 × 10–3 kPa–1 and a fast response time down to 5–7 ms. This demonstration of pressure sensors shows great potential in the applications of electronic skin and wearable devices.

Restacked MoS(2) with enlarged c lattice parameter and surface area was prepared by exfoliation and restacking process, exhibiting high reversible lithium storage capacity and superior rate capability as anode material for lithium ion batteries.

Abstract In view of increasing drug resistance, ecofriendly photoelectrical materials are promising alternatives to antibiotics. Here we design an interfacial Schottky junction of Bi 2 S 3 /Ti 3 C 2 T x resulting from the contact potential difference between Ti 3 C 2 T x and Bi 2 S 3 . The different work functions induce the formation of a local electrophilic/nucleophilic region. The self-driven charge transfer across the interface increases the local electron density on Ti 3 C 2 T x . The formed Schottky barrier inhibits the backflow of electrons and boosts the charge transfer and separation. The photocatalytic activity of Bi 2 S 3 /Ti 3 C 2 T x intensively improved the amount of reactive oxygen species under 808 nm near-infrared radiation. They kill 99.86% of Staphylococcus aureus and 99.92% of Escherichia coli with the assistance of hyperthermia within 10 min. We propose the theory of interfacial engineering based on work function and accordingly design the ecofriendly photoresponsive Schottky junction using two kinds of components with different work functions to effectively eradicate bacterial infection.

Earth-abundant, low-cost electrocatalysts with outstanding catalytic activity in the electrochemical hydrogen evolution reaction (HER) are critical in realizing the hydrogen economy to lift our future welfare and civilization. Here we report that excellent HER activity has been achieved with three-dimensional core/shell Co/Co3O4 nanosheets composed of a metallic cobalt core and an amorphous cobalt oxide shell. A benchmark HER current density of 10 mA cm(-2) has been achieved at an overpotential of ∼90 mV in 1 M KOH. The excellent activity is enabled with the unique metal/oxide core/shell structure, which allows high electrical conductivity in the core and high catalytic activity on the shell. This finding may open a door to the design and fabrication of earth-abundant, low-cost metal oxide electrocatalysts with satisfactory hydrogen evolution reaction activities.

The application of photothermal therapy to treat bacterial infections remains a challenge, as the high temperatures required for bacterial elimination can damage healthy tissues. Here, we develop an exogenous antibacterial agent consisting of zinc-doped Prussian blue (ZnPB) that kills methicillin-resistant Staphylococcus aureus in vitro and in a rat model of cutaneous wound infection. Local heat triggered by the photothermal effect accelerates the release and penetration of ions into the bacteria, resulting in alteration of intracellular metabolic pathways and bacterial killing without systemic toxicity. ZnPB treatment leads to the upregulation of genes involved in tissue remodeling, promotes collagen deposition and enhances wound repair. The efficient photothermal conversion of ZnPB allows the use of relatively few doses and low laser flux, making the platform a potential alternative to current antibiotic therapies against bacterial wound infections.

Intelligent vehicles (IVs) have gained worldwide attention due to their increased convenience, safety advantages, and potential commercial value. Despite predictions of commercial deployment by 2025, implementation remains limited to small-scale validation, with precise tracking controllers and motion planners being essential prerequisites for IVs. This article reviews state-of-the-art motion planning methods for IVs, including pipeline planning and end-to-end planning methods. The study examines the selection, expansion, and optimization operations in a pipeline method, while it investigates training approaches and validation scenarios for driving tasks in end-to-end methods. Experimental platforms are reviewed to assist readers in choosing suitable training and validation strategies. A side-by-side comparison of the methods is provided to highlight their strengths and limitations, aiding system-level design choices. Current challenges and future perspectives are also discussed in this survey.

We report a bio-inspired design strategy for constructing an in situ polymeric SEI in aqueous Zn chemistry. This SEI can restrain interfacial side reactions, facilitate a uniform Zn 2+ flux, and consequently endow a highly stable Zn metal anode.

Summary BACKGROUND The outbreak of a novel coronavirus (SARS-CoV-2, previously provisionally named 2019 novel coronavirus or 2019-nCoV) since December 2019 in Wuhan, China, has become an emergency of major international concern. Apart from the respiratory system, it is unclear whether SARS-CoV-2 can also directly infect other tissues such as the kidney or induce acute renal failure. METHODS We conducted a retrospective analysis of estimated glomerular filtration rate (eGFR) along with other clinical parameters from 85 patients with laboratory-confirmed COVID-19 admitted to a hospital in Wuhan from January 17, 2020 to March 3, 2020. Kidney tissues from six patients with postmortem examinations were analyzed by Hematoxylin and Eosin (H&E) and in situ expression of viral nucleocaspid protein (NP) antigen, immune cell markers (CD8, CD68 and CD56) and the complement C5b-9 was detected by immunohistochemistry. Moreover, the viral particles in kidneys were also investigated by transmission electronic microscope (EM). RESULTS 27.06% (23/85) patients exhibited acute renal failure (ARF). The eldery patients and cases with comorbidities such as hypertension and heart failure more easily developed ARF (65.22% vs 24.19%, p < 0.001; 69.57% vs 11.29%, p < 0.001, respectively). H&E staining demonstrated kidney tissues from postmortems have severe acute tubular necrosis and lymphocyte infiltration. Immunohistochemistry showed that SARS-CoV-2 NP antigen was accumulated in kidney tubules. EM observation also demonstrated that viruses-like particles are visible in the kidneys. Viral infection not only induces CD68 + macrophages infiltrated into tubulointerstitium, but also enhances complement C5b-9 deposition on tubules. CONCLUSIONS SARS-CoV-2 induces ARF in COVID-19 patients. Viruses directly infect human kidney tubules to induce acute tubular damage. The viruses not only have direct cytotoxicity, but also initiate CD68 + macrophage together with complement C5b-9 deposition to mediate tubular pathogenesis.

Abstract Bone‐implant‐associated infections are common after orthopedic surgery due to impaired host immune response around the implants. In particular, when a biofilm develops, the immune system and antibiotic treatment find it difficult to eradicate, which sometimes requires a second operation to replace the infected implants. Most strategies have been designed to prevent biofilms from forming on the surface of bone implants, but these strategies cannot eliminate the biofilm when it has been established in vivo. To address this issue, a nonsurgical, noninvasive treatment for biofilm infection must be developed. Herein, a red‐phosphorus–IR780–arginine–glycine–aspartic‐acid–cysteine coating on titanium bone implants is prepared. The red phosphorus has great biocompatibility and exhibits efficient photothermal ability. The temperature sensitivity of Staphylococcus aureus biofilm is enhanced in the presence of singlet oxygen ( 1 O 2 ) produced by IR780. Without damaging the normal tissue, the biofilm can be eradicated through a safe near‐infrared (808 nm) photothermal therapy at 50 °C in vitro and in vivo. This approach reaches an antibacterial efficiency of 96.2% in vivo with 10 min of irradiation at 50 °C. Meanwhile, arginine–glycine–aspartic‐acid–cysteine decorated on the surface of the implant can improve the cell adhesion, proliferation, and osteogenic differentiation.

The hallmark of the spin-Hall insulator is the presence of gapless edge states of different spins moving in opposite directions. Through analytical solutions in a model calculation for a strip of finite width, we find that edge states on the two sides can couple together to produce a gap in the spectrum, destroying the quantum spin-Hall effect. The application of a magnetic field can however modify and even remove the gap by shifting the momenta of the edge states relative to each other.

Some infectious or malignant diseases such as cancers are seriously threatening the health of human beings all over the world. The commonly used antibiotic therapy cannot effectively treat these diseases within a short time, and also bring about adverse effects such as drug resistance and immune system damage during long-term systemic treatment. Phototherapy is an emerging antibiotic-free strategy to treat these diseases. Upon light irradiation, phototherapeutic agents can generate cytotoxic reactive oxygen species (ROS) or induce a temperature increase, which leads to the death of targeted cells. These two kinds of killing strategies are referred to as photodynamic therapy (PDT) and photothermal therapy (PTT), respectively. So far, many photo-responsive agents have been developed. Among them, the metal-organic framework (MOF) is becoming one of the most promising photo-responsive materials because its structure and chemical compositions can be easily modulated to achieve specific functions. MOFs can have intrinsic photodynamic or photothermal ability under the rational design of MOF construction, or serve as the carrier of therapeutic agents, owing to its tunable porosity. MOFs also provide feasibility for various combined therapies and targeting methods, which improves the efficiency of phototherapy. In this review, we firstly investigated the principles of phototherapy, and comprehensively summarized recent advances of MOF in PDT, PTT and synergistic therapy, from construction to modification. We expect that our demonstration will shed light on the future development of this field, and bring it one step closer to clinical trials.